Heat Transfer Fluid Silicone Fluids MATHERM MFS600
Silicone-based heat transfer fluid providing exceptional thermal stability and wide temperature range for specialized applications. Offers superior oxidation resistance and long service life in demanding high-temperature operations.
Industry Applications:
Key Features
Applications
Served Industries
Technical Data Sheet
Typical technical characteristics and operating guidance for Heat Transfer Fluid Silicone Fluids MATHERM MFS600.
| Property | Test Method | Typical Value |
|---|---|---|
| Operating Temperature | — | -40°C to +300°C(intermittent peak) |
| Flash Point (Open) | ASTM D92 | >190°C |
| Viscosity @ 25°C | ASTM D445 | ~50 cSt |
| Composition | — | Polydimethylsiloxane (PDMS) |
| Appearance | Visual | Clear colorless to pale yellow liquid |
| Density @ 25°C | — | ~970 kg/m³ |
| Pour Point | ASTM D97 | <-50°C |
Operating Parameters
Temperature Range
-40°C to +300°C
(continuous service)
Viscosity @ 25°C
~50 cSt
Service Life
Condition dependent
Consistent Performance
Formulations are developed for stable viscosity, wear protection and contamination control across the stated operating range.
Optimized Formulation
Engineered for stable film strength and anti-wear performance, supporting longer service intervals where operating conditions and oil analysis allow.
Quality Assured
Manufactured under ISO 9001:2015 quality management system with full batch traceability and certificate of analysis.
Application Guide
Step-by-step instructions for optimal use of Heat Transfer Fluid Silicone Fluids MATHERM MFS600 in General Industrial applications.
Preparation
Ensure the application surface is clean, dry, and free from contaminants. Remove any existing lubricant residues using appropriate cleaning agents. For High-temperature reactors applications, verify equipment is at operating temperature.
Application Method
Apply Heat Transfer Fluid Silicone Fluids MATHERM MFS600 using standard industrial equipment. For grease products, use automatic lubrication systems or manual grease guns. For liquid lubricants, ensure proper filling procedures and avoid contamination during transfer.
Recommended Dosage
Follow OEM recommendations for fill quantities. For General Industrial applications, typical re-lubrication intervals range from 1,000 to 5,000 operating hours depending on conditions. Monitor performance and adjust intervals based on actual operating parameters.
Performance Monitoring
Regularly inspect lubricant condition and equipment performance. Check for signs of degradation, contamination, or unusual wear. Schedule oil analysis every 6 months for critical applications to optimize maintenance intervals.
Storage Recommendations
- Store in a cool, dry place between 5°C and 35°C
- Keep containers sealed when not in use
- Avoid direct sunlight and moisture exposure
- Shelf life: 5 years from manufacture date when stored properly
Safety Information
- Refer to Safety Data Sheet (SDS) before use
- Use appropriate PPE: gloves and safety glasses
- Ensure adequate ventilation in application area
- Dispose of used lubricant according to local regulations
Related Products
Coolant Heat Transfer Fluid MATHERM-BTC66
Advanced coolant heat transfer fluid offering superior performance at extreme temperatures up to 120°C. It is a high performance heat transfer fluid made from a mixture of Ethylene Glycol.
Coolant Heat Transfer Fluid MATHERM-SR50
A heat transfer fluid is a formulation of high weight percent ethylene glycol and a specially designed package of industrial corrosion inhibitors. The fluid is dyed fluorescent pink for leak detection purposes. Solutions of this in water provide freeze protection to below -50°C (-60°F) and burst protection to below -73°C (-100°F). It is widely used within the HVAC industry or wherever low freezing water based heat transfer fluids are needed.
Coolant Heat Transfer Fluid MATHERM-MF90
With the continual advancements of micro-processor technology, leading to increasingly higher heat loads, MATHERM-MF90 is the optimal fluid for efficient heat removal in Technology Cooling Systems (TCS). With customized inhibitor packages, this fluid provides superior corrosion protection for liquid cooled, direct-to-chip applications with high surface area copper components. PCBA can be dip into the fluid. MATHERM-MF90 is NON-DG Chemicals, and super coolant of PFPE fluid. Operate range -90°C to +150°C.